Peningkatan Kualitas Udang Rebon Kering Multirespon Mengintegrasikan Metode Taguchi Gray Relational Analysis dan Principal Component Analysis

Nabila Rahmawati, M. Hanifuddin Hakim, Ridho Akbar

Abstract

Rebon shrimp is the catch of fishermen around Sukolilo Baru area, Bulak District of Surabaya. Rebon shrimp processing is only sorted and then dried and sold to collectors. However, the drying process has no definite parameters of factors that can affect the quality of dried rebon shrimp. In overcoming this, research was conducted on improving the quality of dried rebon shrimp. The increase certainly raised several quality responses, namely the color and moisture content of rebon shrimp. The resulting multiresponse needed to be converted into a single response. To optimize multiresponse into a single response, the Taguchi method was used in combination with the Gray Relational Analysis (GRA) and Principal Component Analysis (PCA) methods. Factors and levels were the volume of rebon shrimp (A) with levels of 4 Kg, 4.5 Kg, and 5 Kg, drying time (B) with levels of 90 minutes, 120 minutes, and 150 minutes, and drying temperatures (C) with levels of 41-44ºC, 45-49 ºC, and 36-40 ºC. The quality characteristics were nominal that was the best (if the resulting value is close to the target value, the quality is better). The result produced PCA weighting values on PC1 as evidenced by eigen>1 values. The optimal combination is the volume factor of rebon shrimp at the level of 4.5 Kg, the drying time factor of 120 minutes, and the drying temperature factor of 45 – 49 ºC.

Keywords

Gray Relational Analysis, Multiresponse Optimization, Principal Component Analysis, Quality, Taguchi

Full Text:

PDF

References

P. P. Akbar, A. Solichin, and S. W. Saputra, “Analisis Panjang-Berat dan Faktor Kondisi pada Udang Rebon (Acetes japonicus) di Perairan Cilacap, Jawa Tengah,” Manag. Aquat. Resour. J., vol. 2, no. 3, pp. 161–169, 2013, doi: 10.14710/marj.v2i3.4211.

J. Aghnia, A. Try, M. H. Hakim, and R. Irmawanto, “Rancang Bangun Mesin Pengering Udang Rebon dengan Sistem Kontrol Otomatis Guna Meningkatkan Produktivitas Nelayan,” vol. 5, no. 01, 2022.

BMKG, “Prakiraan Musim Hujan 2022/2023 Di Indonesia,” pp. 1–69, 2022.

M. H. Hakim and M. L. Singgih, “Reduction defect in sewing work stations by integrating OTSM-TRIZ and FMEA,” IPTEK J. Proc. Ser., no. 5, pp. 495–501, 2019.

M. Firdaus, C. A. Intyas, and Y. Yahya, “Peningkatan Kapasitas Produksi Terasi Rebon di Desa Ketapang, Kotamadya Probolinggo,” PengabdianMu J. Ilm. Pengabdi. Kpd. Masy., vol. 6, no. 3, pp. 285–290, 2021, doi: 10.33084/pengabdianmu.v6i3.1832.

N. Fitria, “Analisis Metode Desain Eksperimen Taguchi dalam Optimasi Karakteristik Mutu,” Cent. Libr. Maulana Malik Ibrahim Malang, vol. 19, no. 1, pp. 1–111, 2019.

A. Wulandari, T. Wuryandari, and D. Ispriyanti, “Penerapan Metode Taguchi Untuk Kasus Multirespon Menggunakan Pendekatan Grey Relational Analysis Dan Principal Component Analysis (Studi Kasus Proses Freis Komposit Gfrp),” None, vol. 5, no. 4, pp. 791–800, 2016.

S. B. Sutono, “Grey-based Taguchi Method to Optimize the Multi-response Design of Product Form Design,” J. Optimasi Sist. Ind., vol. 20, no. 2, pp. 136–146, 2021.

N. Jain and R. Kumar, “Multi-response optimization of process parameters in friction stir welded aluminum 6061-T6 alloy using Taguchi grey relational analysis,” World J. Eng., vol. 19, no. 5, pp. 707–716, 2022.

F. Arifin, A. Zamheri, Y. D. Herlambang, A. P. Syahputra, I. Apriansyah, and F. Franando, “Optimization of Process Parameters in 3D Printing FDM by Using The Taguchi and Grey Relational Analysis Methods,” SINTEK J. J. Ilm. Tek. Mesin, vol. 15, no. 1, pp. 1–10, 2021.

A. Syukron and M. Kholil, Six Sigma Join.Pdf. Yogyakarta: Graha Ilmu, 2013.

S. Sembiring, “Menyisipkan Pesan Teks Pada Gambar Dengan Metode End of File,” Pelita Inform. Budi Darma, vol. IV, pp. 45–51, 2013.

S. Yuliana, “Analisis Daya Tekan dan Daya Serap Pada Batako Menggunakan Pendekatan Grey Relational Analysis dan Principal Component Analysis,” J. Elektro dan Mesin Terap., vol. 8, no. Vol. 8 No. 2 (2022), pp. 81–90, 2022, doi: 10.35143/elementer.v8i2.5740.

R. Devita, S. Si, and M. Si, “Analisis Variansi Galat Mutlak Data Hasil Pengukuran Arus untuk Beberapa Besaran Tegangan pada Suatu Resistansi,” vol. 1, no. November, pp. 43–52, 2021.

Nuryadi, T. D. Astuti, E. S. Utami, and M. Budiantara, Buku Ajar Dasar-dasar Statistik Penelitian. 2017.

U. Usmadi, “Pengujian Persyaratan Analisis (Uji Homogenitas Dan Uji Normalitas),” Inov. Pendidik., vol. 7, no. 1, pp. 50–62, 2020, doi: 10.31869/ip.v7i1.2281.

DOI: http://dx.doi.org/10.52759/inventory.v4i2.129

Refbacks

  • There are currently no refbacks.